Shower walls are the single most waste-heavy tiling job in a house, and almost every estimate you will find online is off by 15 to 25 percent because it ignores the two things that actually eat tile: the shower valve cutout and the curb. A standard 60-inch alcove surround is about 70 square feet of wall — but you cannot buy 70 square feet of tile. Here is the arithmetic that gets you to a number you can order against.
Measuring the wall properly
Start with the three walls: back wall 60 inches wide, two side walls typically 30 to 36 inches deep. Height runs from the tub deck or shower pan to the ceiling or a tile border, commonly 72 to 84 inches. For a 60-by-32 alcove with 78-inch walls, the area is (60 + 32 + 32) × 78 ÷ 144 ≈ 67 square feet.
Now subtract the openings: the valve and showerhead trim removes roughly 1 square foot, a niche removes 1.5 to 3, and a window removes its full face area. Most alcoves land between 62 and 68 net square feet. Note the number — it is the base for every calculation that follows.
The waste factor is not a flat 10 percent
This is where estimates go wrong. Waste depends on tile size, layout, and how many cuts land on a visible edge:
| Tile format | Typical waste | Why |
|---|---|---|
| Large-format 12×24 or bigger | 15–20% | Few pieces, so one bad cut costs a whole tile; pattern match across walls |
| Standard 4×8 subway | 10–12% | Small pieces, forgiving cuts, easy to reuse offcuts |
| Mosaic sheets (1×1 or 2×2) | 8–10% | Cut sheets can be reused on the next course |
| Herringbone or chevron | 20–25% | Every edge cut is a diagonal and offcuts are rarely reusable |
| Tile with a strong directional pattern | 18–25% | Grain direction must be maintained; you cannot flip a cut |
For a 66-square-foot alcove in 12×24 tile, the order quantity is 66 × 1.18 ≈ 78 square feet. For subway tile, 66 × 1.11 ≈ 73 square feet. That 5-square-foot difference is roughly one extra box — real money on a premium tile.
If you are working across multiple rooms or want the square-footage conversion handled for you, the area calculator converts your wall measurements into square feet and square meters so the box math lines up with how the tile is sold.
Curb, niche, and the pieces nobody counts
The curb is a frequent omission. A 60-inch curb that is 5 inches wide across the top plus two 5-inch faces is 60 × 15 ÷ 144 ≈ 6.25 square feet — and it usually needs bullnose or a slab, not field tile. Add 6 to 8 square feet for the curb if you are tiling it in the same material.
Niches are worse. A 12×20 niche needs four return pieces plus a sill, and if you are using a contrasting material the count is separate entirely. A framed prefab niche costs more per square foot than the surrounding wall because the pieces are tiny and the cuts are fussy.
Also count the transition at the top if you are running tile to a painted ceiling: you will want a trim piece, and that is linear feet, not square feet.
Thinset and grout follow a different formula
Mortar coverage depends on trowel notch, not wall area alone. A 1/4×3/8 square-notch trowel covers about 60 to 70 square feet per 50-pound bag on a flat substrate; a 1/2×1/2 notch covers 30 to 40. Shower walls are rarely flat, so use the lower end — for 78 square feet of ordered tile, two 50-pound bags of modified thinset is a safe order for a large-format job.
Grout is driven by tile size and joint width. A 12×24 tile with 1/8-inch joints uses roughly 0.6 to 0.9 pounds per 10 square feet, so a 25-pound bag covers about 300 square feet — far more than one shower needs. Small mosaic with 1/8-inch joints consumes 3 to 5 times more grout per square foot and can genuinely require a full bag for a single shower.
For mixing ratios and volume conversions on the thinset and grout side, the volume calculator handles the water-to-powder math in both imperial and metric units.
Ordering: the overage rule
Order all tile for the job in one purchase from one lot. Dye lots vary visibly between batches, and a 5 percent shortfall three weeks later means a mismatched patch or a re-order of the whole wall. The standard contractor rule is to keep one full box unopened as attic stock for future repairs — showers crack, and matching a discontinued tile is impossible.
A practical ordering sequence for a 66-square-foot alcove: 78 square feet of field tile at 18 percent waste, 8 square feet for the curb, 3 square feet for the niche, and one extra box as attic stock. That is about 92 square feet, or four boxes of a 25-square-foot case.
Frequently asked questions
Can I tile over existing tile? You can, and it saves demolition, but the wall area stays the same and the curb gets 3/8 inch thicker, which changes your glass panel measurement. Recount after you decide.
Do I need to subtract the tub? Yes. Tile starts at the tub deck, not the floor. Measuring from the floor overstates the wall by 12 to 18 inches of height on the long wall.
How much extra for a diagonal layout? Budget 20 percent rather than 10 to 12, because every perimeter cut becomes an angled cut and the offcuts rarely work elsewhere.
Is 20 percent waste too much? Not for large-format or patterned tile. It is excessive for subway tile, where 10 to 12 percent is enough and the leftovers become your attic stock.
The number to remember
Net wall area times 1.15 to 1.20, plus 8 square feet for the curb, plus the niche, plus one unopened box. For a typical 60-inch alcove that lands near 90 square feet of tile for a job that measures 66. Ordering to the measured number instead of the calculated number is the most common way a shower tiling project stalls halfway up the back wall.

Leave a Reply
You must be logged in to post a comment.